Lesson 5: Motherboards, CPUs and Power
CompTIA A+ Core 1 (220-1201) · Objectives 220-1201 3.5, 220-1201 3.6 · Download .docx
Objectives
- Install and configure motherboards, CPUs and add-on cards: form factors, sockets, headers, BIOS/UEFI settings and cooling.
- Install or replace the right power supply: connectors, wattage, rails, efficiency and redundancy.
Key terms
- Motherboard
- Main circuit board connecting the CPU, memory, storage, expansion cards and power, providing the chipset and firmware.
- PSU
- Power supply unit: component converting wall AC power into the regulated DC voltages a computer's parts need.
- ATX
- Advanced Technology Extended: standard full-size motherboard form factor, 12 by 9.6 inches, with up to seven expansion slots.
- Input voltage (110-120 VAC vs. 220-240 VAC)
- Wall power standards: 110-120 volts AC in North America and 220-240 volts AC in much of the world; supplies must match or auto-switch.
- microATX
- Smaller ATX-compatible motherboard, 9.6 by 9.6 inches, with up to four expansion slots and mounting holes that fit ATX cases.
- 12 V rail
- Power supply output feeding the most demanding parts, including CPU voltage regulators, graphics cards, fans and drive motors.
- ITX
- Information Technology eXtended: very small motherboard family, most commonly mini-ITX at 6.7 by 6.7 inches with one expansion slot.
- 5 V rail
- Power supply output used by USB ports, some drive electronics and other logic circuitry.
- PCI
- Peripheral Component Interconnect: legacy parallel expansion slot with a shared bus, replaced by PCIe but still found on some older boards.
- 3.3 V rail
- Lowest main power supply output, used by some chipset, memory and M.2 and PCIe slot circuits.
- 24-pin motherboard power connector
- Main power plug from the power supply to the motherboard, often built as 20 pins plus a detachable 4-pin piece for older boards.
- Redundant power supply
- Server design with two or more power supplies sharing the load so the system keeps running if one fails; units are often hot-swappable.
- CPU power connector
- Separate 4- or 8-pin 12 V power connector near the processor socket that feeds the CPU's voltage regulators.
- Modular power supply
- Power supply whose output cables detach, so only needed cables are installed, improving airflow and cable management.
- PCIe power connector
- Power supply cable that delivers additional 12 V power directly to high-wattage graphics cards.
The concept
220-1201 3.5 — Install and configure motherboards, CPUs and add-on cards: form factors, sockets, headers, BIOS/UEFI settings and cooling. M.2 slot location: Letter E is the M.2 slot: a short horizontal socket with a standoff that holds the far end of the card with a screw. NVMe M.2 SSDs connect directly to PCIe lanes through this socket, so no separate data or power cable is needed. CMOS battery reset: Letter G is the CMOS battery, a coin cell (usually CR2032) that keeps the real-time clock running and, on many boards, preserves firmware settings while the PC is unplugged. Removing it with AC power disconnected lets the settings revert to defaults. Mini-ITX form factor: Mini-ITX boards measure 170 × 170 mm (6.7 × 6.7 in) and typically provide one PCIe x16 expansion slot and two DIMM slots. Their small size suits compact, quiet systems such as media PCs. microATX form factor: microATX boards are square, at most 244 × 244 mm, and support up to four expansion slots. Because they share mounting-hole positions and the I/O shield size with ATX, they fit nearly all ATX cases, which makes them a common choice for budget and school-lab builds. Secure Boot: Secure Boot is a UEFI feature that checks the digital signature of each boot component against trusted keys stored in firmware and refuses to run anything unsigned or revoked. This blocks bootkits and unauthorized boot media. TPM and BitLocker: A Trusted Platform Module is a secure cryptoprocessor that stores keys and records measurements of the boot process. BitLocker seals its key to those measurements, so the TPM releases it only when firmware and boot files are unchanged.
220-1201 3.6 — Install or replace the right power supply: connectors, wattage, rails, efficiency and redundancy. 12V-2x6 GPU connector: Letter F is the 12V-2x6 connector: 12 power pins plus 4 sense pins, rated for up to 600 W. It revises the earlier 12VHPWR design so the card draws full power only when the plug is completely seated. SATA power connector: Letter D is the 15-pin SATA power connector, a flat L-shaped plug that can supply 3.3 V, 5 V and 12 V to SATA devices. A 2.5-inch SSD typically uses only the 5 V line, but the connector is the same for all SATA drives. PSU wattage headroom: Required capacity = 485 W × 1.25 = 606.25 W, so the 650 W unit is the smallest listed that exceeds it. Headroom keeps the PSU in its efficient load range, absorbs short power spikes from graphics cards, and leaves room for future upgrades. auto-switching input voltage: A PSU rated 100–240 V, 50/60 Hz is auto-switching (wide-range): it accepts both North American (about 120 V) and most international (220–240 V) supplies. Only the plug shape differs, so a simple outlet adapter is enough. modular PSU: A modular power supply lets the installer attach only the cables that are needed. Fully modular units detach every cable, including the 24-pin and CPU cables, while semi-modular units keep those fixed. redundant power supplies: Redundant power supplies share the load, and if one fails the other carries the whole load. Hot-swappable units slide out of the chassis and can be replaced while the server runs.
Worked examples
Common mistakes
- Hardware security module: choosing “Self-encrypting drive” is a common mistake. A self-encrypting drive protects the data on that drive; it does not perform signing for other systems.
- 24-pin main connector location: choosing “Letter A” is a common mistake. Letter A is the CPU socket.
- Hardware security module: choosing “Secure Boot” is a common mistake. Secure Boot is a firmware feature that checks bootloader signatures, not a key store.
- TPM and BitLocker: choosing “A supervisor password” is a common mistake. A supervisor password protects firmware settings but provides no key storage.
- modular PSU: choosing “Single 12 V rail design” is a common mistake. Rail design affects how 12 V current is distributed and protected, not which cables are attached.
- 12V-2x6 GPU connector: choosing “Letter C” is a common mistake. Letter C is the PCIe 6+2-pin connector, used by cards with 6- or 8-pin sockets, not a 16-pin socket.
Self-check
Try each one before you look. A miss here costs nothing and tells you exactly what to reread.
Canvas is the official record. This companion enhances the PGCC curriculum; it does not replace it. Last name and class year only. Students with a 504 plan or IEP: your accommodations apply.