P-TECH IT
All P-TECH sites online· 9:15 PM Eastern, open the status page

Lesson 6: Cables, RAM and Storage

CompTIA A+ Core 1 (220-1201) · Objectives 220-1201 3.2, 220-1201 3.3, 220-1201 3.4 · Download .docx

Objectives

Key terms

Twisted-pair cable
Copper cable with pairs of insulated wires twisted together to cancel electromagnetic interference, used for Ethernet and phone lines.
DIMM
Dual In-line Memory Module: full-size memory stick for desktops and servers; DDR4 and DDR5 versions have 288 pins.
Spindle speed
Rotation rate of a hard drive's platters in revolutions per minute, such as 5400, 7200, 10000 or 15000; faster improves access time.
Cable category
TIA rating for twisted-pair cable that indicates its tested frequency and supported Ethernet speeds, such as Cat 5e, 6, 6a and 8.
SODIMM
Small Outline Dual In-line Memory Module: compact, shorter memory module used in laptops, mini PCs and some all-in-ones.
2.5-inch drive
Smaller drive form factor used for laptop hard drives and most SATA SSDs.
Cat 5e
Enhanced Category 5 twisted-pair cable supporting Gigabit Ethernet up to 100 meters; the minimum for most new networks.
DDR
Double Data Rate: memory technology that transfers data on both the rising and falling edge of the clock, doubling throughput.
3.5-inch drive
Larger desktop and server hard drive form factor that holds more platters and capacity and needs 12 V power.
Cat 6
Twisted-pair cable rated to 250 MHz supporting 1 Gbps to 100 meters and 10 Gbps for runs up to about 55 meters.
DDR3
Third-generation DDR memory using 240-pin desktop DIMMs at about 1.5 volts; physically keyed so it cannot fit DDR4 slots.
NVMe
Non-Volatile Memory Express: storage protocol designed for flash that talks to SSDs directly over PCIe lanes with many parallel queues, far faster than SATA.
Cat 6a
Augmented Category 6 twisted-pair cable rated to 500 MHz, supporting 10 Gbps Ethernet across the full 100-meter distance.
DDR4
Fourth-generation DDR memory using 288-pin DIMMs at 1.2 volts with speeds commonly from 2133 to 3200 MT/s.
SATA SSD
Solid-state drive using the SATA interface and AHCI protocol, limited to about 600 MB/s by the 6 Gbps link.

The concept

220-1201 3.2 — Compare cable types and connectors: network, video, peripheral, storage and adapters. USB 3.2 speed tiers: USB 3.2 Gen 1 runs at 5 Gbps, Gen 2 at 10 Gbps, and Gen 2x2 at 20 Gbps (two lanes, USB-C only). USB4 reaches 40 Gbps (80 Gbps in USB4 Version 2.0), and USB 2.0 is 480 Mbps. Thunderbolt docking: Thunderbolt 4 uses the USB-C connector and provides 40 Gbps, tunneling PCIe and DisplayPort traffic over a single cable, with mandatory support for two 4K displays. Those guarantees make it the standard choice for single-cable docks that also host fast external storage. DVI variants: DVI-I (integrated) includes both the digital TMDS pins and the four analog pins arranged around the flat ground blade. Because it carries analog RGB, a simple passive adapter can convert DVI-I to VGA. VGA analog connector: Connector D is VGA, a 15-pin, three-row D-subminiature (DE-15) connector that carries analog RGB video plus sync signals. It is the only purely analog connector among the choices. DisplayPort MST: Connector B is DisplayPort, recognizable by its single cut corner. DisplayPort's Multi-Stream Transport sends several independent video streams over one connection, so compatible monitors can be daisy-chained or fed from an MST hub. Cat 6a 10 Gbps distance: Cat 6a (augmented Category 6) is rated to 500 MHz and supports 10GBASE-T over the full 100 m channel. Cat 6 can carry 10 Gbps only on shorter runs (roughly 37–55 m, depending on alien crosstalk), so a 90 m link requires Cat 6a.

220-1201 3.3 — Compare RAM characteristics: DDR4 vs DDR5, DIMM vs SO-DIMM, ECC, channels and capacity limits. DDR4 vs DDR5 keying: DDR4 and DDR5 DIMMs are the same length and both have 288 pins, but the notch sits at a different point along the edge connector. The keying stops a technician from inserting a module whose voltage, signaling and power design (DDR5 adds an on-module PMIC) the board cannot support. SODIMM selection: Small Outline DIMMs (SODIMMs) are about 69.6 mm long, roughly half the length of a desktop DIMM, and are used in laptops, mini PCs and some all-in-ones. DDR5 SODIMMs have 262 pins, matching the listed specification, while DDR4 SODIMMs have 260. ECC memory: Error-correcting code (ECC) memory stores extra check bits with each data word so the memory controller can correct single-bit errors and detect multi-bit errors. ECC works only when the CPU and motherboard support it, which is why it is standard on servers and workstations. dual-channel slot placement: In a dual-channel system the memory controller has two independent 64-bit channels, A and B. Placing one module in each channel lets the controller access both at the same time, doubling theoretical bandwidth. memory bandwidth calculation: Peak bandwidth = transfers per second × bytes per transfer. A 64-bit data width moves 8 bytes per transfer, so 5,600 MT/s × 8 B = 44,800 MB/s = 44.8 GB/s. 32-bit address limit: A 32-bit OS can address 2^32 bytes = 4 GiB in total, and part of that address space is reserved for devices, leaving roughly 3–3.5 GB usable. Because the firmware sees all 16 GB, the hardware is fine.

220-1201 3.4 — Compare storage devices: HDD, SATA and NVMe SSD, M.2 keys and sizes, form factors and RAID levels. HDD rotational latency: One revolution takes 60 s ÷ 7,200 = 0.00833 s = 8.33 ms. On average the desired sector is half a revolution away, so average rotational latency = 8.33 ÷ 2 ≈ 4.17 ms. NVMe vs SATA SSD: NVMe is a storage protocol designed for flash that runs directly over PCIe lanes. A PCIe 4.0 x4 link provides roughly 7.9 GB/s (16 GT/s per lane × 4 lanes, less encoding overhead), so NVMe drives can read around 7,000 MB/s, more than ten times the SATA III ceiling. M.2 keying and protocol: M.2 is a form factor, not a protocol. A B+M-keyed SATA SSD fits mechanically into an M-key socket, but if the socket is wired only for PCIe lanes, there is no SATA path to the drive and the system will not detect it. M.2 size codes: M.2 size codes list width and then length in millimeters, so 2280 = 22 mm × 80 mm. Common sizes are 2230, 2242, 2260 and 2280; 2280 is the most common desktop and laptop SSD size, while 2230 is common in handhelds and compact laptops. RAID 5 capacity: RAID 5 stripes data with distributed parity and uses one drive's worth of capacity for parity: (n − 1) × size = (4 − 1) × 4 TB = 12 TB. It survives the failure of any one drive; a second failure before the rebuild finishes destroys the array. RAID 6 vs RAID 10: RAID 6 stripes data with two independent parity blocks, so any two drives can fail without data loss. Usable capacity is (n − 2) drives, which with six drives is four drives' worth of space, compared with three for RAID 10.

Worked examples

Example 1: A school needs a 10 Gbps copper Ethernet link between two wiring closets. The total cable run, including patch cords, is 90 meters. Which is the minimum cable category that supports 10GBASE-T over this distance? Answer: Cat 6a. Cat 6a (augmented Category 6) is rated to 500 MHz and supports 10GBASE-T over the full 100 m channel. Cat 6 can carry 10 Gbps only on shorter runs (roughly 37–55 m, depending on alien crosstalk), so a 90 m link requires Cat 6a. Cat 8 is faster but is limited to 30 m data-center runs.
Example 2: A motherboard has four DIMM slots labeled A1, A2, B1 and B2, and the manual recommends A2 and B2 when two modules are installed. A technician is installing two identical 16 GB modules. Which placement enables dual-channel operation? Answer: One module in A2 and one in B2. In a dual-channel system the memory controller has two independent 64-bit channels, A and B. Placing one module in each channel lets the controller access both at the same time, doubling theoretical bandwidth. Boards usually specify the second slot of each channel (A2 and B2) first for best signal quality, so following the manual matters.
Example 3: A video editor wants the fastest possible scratch volume from two identical SSDs, with the full combined capacity of both. Finished projects are backed up elsewhere, so fault tolerance is not required. Which RAID level fits? Answer: RAID 0. RAID 0 stripes data across all member drives, which raises throughput and uses 100% of the capacity, but it has no redundancy: if one drive fails, the whole array is lost. That is acceptable only for data that is backed up or easy to recreate.

Common mistakes

Self-check

Try each one before you look. A miss here costs nothing and tells you exactly what to reread.

1. Which connector is threaded and is used to terminate RG-6 coaxial cable at a cable modem or TV?
2. A technician tries to install a DDR5 DIMM in a desktop motherboard that has DDR4 slots, and the module will not seat. What is the reason?
3. A laptop's M.2 slot is M-keyed, and its documentation states "PCIe NVMe only." A technician installs an M.2 SATA SSD that has a B+M key. What will most likely happen?
4. A student connects a gaming PC to a TV that supports 4K at 120 Hz over HDMI 2.1. The picture flickers or drops out at 120 Hz but is stable at 4K 60 Hz. Both devices are set correctly, and the cable is an older High Speed HDMI cable. What should the technician do?
5. A technician adds a DDR4-2666 module to a system that already has a DDR4-3200 module of the same capacity. Both modules are detected. How will the memory most likely operate?

Canvas is the official record. This companion enhances the PGCC curriculum; it does not replace it. Last name and class year only. Students with a 504 plan or IEP: your accommodations apply.

← Lesson 5: Motherboards, CPUs and PowerLesson 7: Displays and Printers →

↑ Back to top