P-TECH IT
All P-TECH sites online· 9:15 PM Eastern, open the status page

Lesson 10: Hardware, Display, Mobile and Printer Troubleshooting

CompTIA A+ Core 1 (220-1201) · Objectives 220-1201 5.1, 220-1201 5.2, 220-1201 5.3, 220-1201 5.4, 220-1201 5.6 · Download .docx

Objectives

Key terms

POST
Power-on self-test: diagnostic routine the firmware runs at startup to check CPU, memory and video before loading the operating system.
Drive LED status indicators
Lights on drives, bays or enclosures showing activity, health or failure, often amber or red for a faulty drive.
Incorrect input source
Display problem where a monitor, TV or projector is set to a different input port than the one the computer is connected to.
Poor battery health
Battery that has lost much of its original capacity through age and charge cycles, giving short runtime and needing replacement.
Lines down the printed pages
Printer symptom of vertical streaks, usually from a scratched drum or dirty components in laser printers or clogged nozzles in inkjets.
POST beeps
Patterns of startup beeps from the motherboard that signal which hardware failed testing, such as memory or video, before anything displays.
Grinding noises (drive)
Harsh scraping sound from a hard drive indicating heads or bearings physically damaging platters; back up and replace immediately.
Physical cabling issues
Display problems caused by loose, damaged, wrong or too-long video cables, producing no signal, flicker or color loss.
Swollen battery
Lithium battery that has expanded from internal gas buildup, pushing on cases or screens; a fire hazard requiring immediate safe removal.
Garbled print
Pages printing random symbols or nonsense characters, usually caused by a wrong or corrupted driver or a bad connection.
Proprietary crash screens
Umbrella term for the full-screen fatal error displays each operating system shows when its kernel halts, such as macOS and Linux kernel panics.
Clicking sounds
Repeated ticking from a hard drive as its heads fail to read and reset, a classic sign of imminent mechanical failure.
Burnt-out bulb
Projector symptom where the lamp no longer lights or is very dim because it has reached the end of its rated hours.
Broken screen
Physically cracked or shattered display glass that may still show an image but risks cuts and touch failure.
Paper jams
Paper stuck in the printer's path, caused by worn rollers, wrong paper type, damp paper, overfilled trays or debris.

The concept

220-1201 5.1 — Troubleshoot motherboard, RAM, CPU and power problems. POST beep codes: POST beep codes are produced by the firmware when a hardware test fails before video is available. Their meaning differs between firmware vendors and board models, so the technician should consult the motherboard or firmware documentation for that exact pattern. Stop error after driver update: A stop error (CompTIA's "proprietary crash screen," commonly called a BSOD) that begins right after a driver update points to that driver. Rolling back the driver in Device Manager, or from Safe Mode if needed, tests the theory quickly. macOS kernel panic: A kernel panic is the macOS (and Linux) equivalent of a Windows stop error: the OS core hits an error it cannot recover from and the system restarts. macOS then reports that the computer restarted because of a problem. Blank screen with discrete GPU: When a dedicated graphics card is installed, most boards disable the onboard video outputs, so plugging the monitor into the motherboard port produces a blank screen. Because the problem began after recabling and the monitor is known good, the cable location is the obvious first check. Power supply tester: A power supply tester connects to the PSU's 24-pin and other connectors and shows whether each voltage rail (such as +3.3 V, +5 V, and +12 V) is within tolerance. A multimeter can also be used. Thermal throttling: Modern CPUs automatically lower their clock speed when they reach a temperature limit, which is called thermal throttling. A sharp clock drop combined with a loud fan and hot case points to blocked vents, dust in the heat sink fins, or a failing fan.

220-1201 5.2 — Troubleshoot storage drive and RAID problems. HDD clicking sound: A repeated click (sometimes called the "click of death") is usually the read/write head assembly failing to find or read its tracks and resetting. It is a strong sign that the drive is about to fail mechanically. Grinding drive and data recovery: A grinding noise usually means physical contact inside the drive, such as a head scraping the platter surface. Every additional minute of power-on time can cause more damage, so the drive should be powered off and sent to a professional recovery service that works in a clean room. S.M.A.R.T. warning: Self-Monitoring, Analysis and Reporting Technology (S.M.A.R.T.) tracks attributes such as reallocated sectors and read errors and warns when they cross failure thresholds. A bad S.M.A.R.T. Boot mode reset: Removing the CMOS battery resets firmware settings to defaults. If the board's default boot mode (for example legacy/CSM instead of UEFI) or boot order differs from how Windows was installed, the firmware cannot find the boot loader even though the drive is detected. Bootable device not found causes: The message comes from firmware when it cannot find a device with a valid boot loader. That happens if the boot drive is disconnected or not detected, or if the boot order points to a device with no boot loader (such as a blank USB drive) and no valid fallback. Drive not detected in firmware: If firmware does not detect a drive, the problem is below the operating system: power, data connection, port, or the drive itself. Reseating the SATA data and power cables (or trying a different port and cable) is the quickest, least invasive test.

220-1201 5.3 — Troubleshoot video, projector and display problems. Incorrect input source: Questioning the obvious means testing the simplest, most likely, and cheapest causes before complex ones. A "No signal" message right after someone else used the room strongly suggests the projector was switched to a different input. Incorrect color via VGA: VGA carries red, green, and blue on separate analog pins. If the green signal is lost through a loose connector or bent pin, the image takes on a pink or magenta cast; losing other pins produces other tints. Burnt-out projector bulb: Lamp-based projectors use a bulb rated for a set number of hours. When it burns out, the fan and electronics still work but nothing is projected, and most models light a lamp warning indicator. Fuzzy image and native resolution: LCD and OLED panels have a fixed grid of pixels, their native resolution. Any other resolution must be scaled to fit the grid, which makes text look soft or fuzzy. Display burn-in prevention: Burn-in happens when static content ages some pixels faster than others, leaving a permanent ghost image; it is most common on OLED and older plasma panels. Rotating content, using pixel-shift features, lowering brightness, and turning the display off when idle spread wear evenly. Dead pixel: A dead pixel receives no power or has failed transistors, so it never lights and appears black. A stuck pixel is lit in a single color and can sometimes be revived with pixel-cycling tools, while a dead pixel usually cannot.

220-1201 5.4 — Troubleshoot common mobile device hardware problems. Poor battery health: Lithium-ion batteries lose capacity with every charge cycle and with age, and a reported maximum capacity around 70-80% is commonly treated as the point where replacement makes sense. Software changes can reduce power use, but only a new battery restores runtime. Swollen battery safety: A swollen lithium-ion battery has built up gas from internal breakdown and is at risk of thermal runaway (fire). Stop using and charging the device, remove the battery carefully without bending or puncturing it, and store it away from flammable materials. Broken screen and digitizer: The digitizer is the transparent touch-sensing layer bonded to the display glass. When the glass cracks, the digitizer can stop sensing touch in that area while the display panel underneath still shows an image. Improper charging wattage: USB-C Power Delivery negotiates voltage and current between the charger and the device. A 5 W adapter cannot supply what a tablet draws under load, so it charges slowly or even drains while plugged in. Physically damaged port: Wireless charging proves the battery and charging circuits work, which isolates the fault to the wired port. A bent or broken contact tongue is physical damage that cleaning cannot fix, so the port (often a small daughterboard or flex assembly) must be replaced. Laptop antenna after repair: Most laptops route their Wi-Fi antenna cables through the display lid because the top of the screen gives the best reception. During a display replacement, the antenna leads can be left unplugged from the wireless card or pinched.

220-1201 5.6 — Troubleshoot printer problems. Vertical line on laser prints: A line in the same position on every page points to a fixed defect along the image path, most often a scratch or debris on the drum (imaging unit); a dirty charging roller or corona wire can cause similar streaks. Printing a page from the printer itself rules out the PC and driver. Garbled print driver: Garbled output, meaning pages of random characters, usually means the printer is receiving commands in a printer language or format it does not understand. Reusing a queue built for a different model sends the wrong driver's output to the new printer. Toner not fusing: In the fusing step, heated rollers melt the toner and press it into the paper fibers. If the fuser is not reaching temperature or is worn, the toner sits loosely on the page and smears. Echo images on prints: A double or echo (ghost) image repeating at a fixed distance means part of the previous image remains on the drum and is printed again on the next rotation. That points to the cleaning stage: a worn cleaning blade or a drum that is not fully erased. Paper not feeding: Pickup rollers use friction to pull the top sheet from the tray. Over time the rubber hardens and glazes, so the rollers slip and the printer reports no paper or jams on pickup. Card stock paper jams: Heavy media is stiff and can jam on the tight bends of a main tray's paper path. Most printers have a bypass (multipurpose) tray with a straighter path, and setting the media type to heavy or card stock adjusts fuser temperature and speed.

Worked examples

Example 1: A technician has confirmed that the outlet, power cord, and power switch are all good, but a desktop still shows no signs of power. Which tool should be used next to check the power supply's output voltages? Answer: Power supply tester. A power supply tester connects to the PSU's 24-pin and other connectors and shows whether each voltage rail (such as +3.3 V, +5 V, and +12 V) is within tolerance. A multimeter can also be used. This isolates the PSU from the motherboard before replacing parts.
Example 2: A video editing workstation stores projects on a two-disk RAID 0 array. One of the disks fails. What is the result? Answer: All data on the array is lost and must be restored. RAID 0 stripes data across disks for speed and offers no fault tolerance. Because each file is split into blocks spread across both disks, losing either disk breaks every file, so the whole array is lost. Data must be restored from backup after replacing the disk and recreating the array.
Example 3: A projector on a cart is tilted upward toward the screen. The image is wider at the top than at the bottom. Which adjustment fixes this? Answer: Keystone correction. When a projector is not square to the screen, the image becomes a trapezoid; this is called keystone distortion. Keystone correction digitally reshapes the image so its sides are parallel again. Physically leveling the projector or using lens shift gives the best image quality when possible.

Common mistakes

Self-check

Try each one before you look. A miss here costs nothing and tells you exactly what to reread.

1. A desktop powers on and its fans spin, but nothing appears on the monitor and the system emits a repeating pattern of short beeps. What is the best next step to interpret the symptom?
2. A desktop reports that no bootable device was found. In firmware setup, the SATA system drive does not appear in the storage list at all. What should the technician do next?
3. A user notices one tiny dot on a new monitor that stays black no matter what image is displayed. What is this called?
4. A three-year-old phone's battery settings report 71% of its original maximum capacity, and a full charge no longer lasts a school day. What is the best long-term fix?
5. Jobs from several users are piling up in a shared laser printer's queue. The first job has shown "Printing" for an hour, nothing has come out, and the printer's control panel is prompting for Legal paper. The tray holds Letter paper. What is the most likely cause of the backlog?

Canvas is the official record. This companion enhances the PGCC curriculum; it does not replace it. Last name and class year only. Students with a 504 plan or IEP: your accommodations apply.

← Lesson 9: Troubleshooting Method and Network TroubleshootingLesson 11: Operating Systems, Installation and Windows Editions →

↑ Back to top